JB15FPG05

Series JB Low Profile Process Sealed Tactiles General Specifications Electrical Capacity (Resistive Load) Low/Logic Level: 50mA 24V DC maximum for Standard Operating Force models 125mA 24V DC maximum for High Operating Force models Other Ratings Standard Operating Force High Operating Force Contact Resistance: 50 milliohms maximum 50 milliohms maximum Insulation Resistance: 500 megohms minimum 250V DC 500 megohms minimum 250V DC Dielectric Strength: 250V AC minimum for 1 minute minimum 250V AC minimum for 1 minute minimum Mechanical Life: 5,000,000 operations minimum 1,000,000 operations minimum Electrical Life: 5,000,000 operations minimum 1,000,000 operations minimum Nominal Operating Force: 1.76N for JB15 2.65N for JB15H Total Travel: .010 (.250mm) .012 (.300mm) Materials & Finishes Actuator: Glass fiber reinforced PBT for Extended actuator PBT for Flat Polyacetal for Short Case: Glass fiber reinforced polyamide (UL94V-0) Seal: Nitrile butadiene rubber Base: Glass fiber reinforced PBT (UL94V-0) Movable Contacts: Stainless steel Stationary Contacts: Brass with silver plating Terminals: Brass with silver plating Mounting Bracket: Phosphor bronze with tin plating Environmental Data Operating Temperature Range: 25C through +70C (13F through +158F) Humidity: 90 ~ 95% humidity for 240 hours 40C (104F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning J in 1 minute 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) PCB Processing Soldering: Wave Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Cleaning: Automated cleaning. See Cleaning specifications in Supplement section. Standards & Certifications Flammability Standards: UL94V-0 rated case & base The JB Series tactiles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. J20 www.nkkswitches.com Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers TogglesLow Profile Process Sealed Tactiles Series JB Distinctive Characteristics Special bracket for right angle mounting provides added design variations. Higher operating force type provides more pronounced operating feel. Rubber seal construction prevents contact contamination and allows automated soldering and cleaning. Choice of dimensions from PCB to top of cap allows design flexibility. Dome contact gives crisp tactile feedback to positively indicate circuit transfer and assures high reliability and long life of up to 5,000,000 operations. Slanted terminals provide a spring type action which ensures secure mounting and prevents dislodging during wave soldering. Actual Size Molded-in terminals are part of the sealed construction which allows automated soldering and washing. Terminal spacing conforms to standard .100 (2.54mm) PCB grid. J Common Bus Matrix X-Y Matrix These single pole, single throw switches can be used in a key- These single pole, single throw switches can be board matrix and, using strapped terminals, achieve a com- arranged on a single-sided PC board matrix mon bus electrical configuration on a single-sided PC board. with strapped terminals to achieve an X-Y type electrical interconnection. 5 9 1 2 3 13 1 2 3 PC Terminations PC Terminations 12 34 56 78 9101112 13 12 34 56 7 1 1 1 2 2 4 5 6 10 4 5 6 3 3 4 2 4 4 6 5 5 6 6 7 8 11 9 7 8 9 7 7 8 6 3 8 8 9 9 0 0 12 A 0 B A 0 B A A 7 1 B B = ON = ON 5 4 3 2 7 Red = PCB Trace Black = Switch Circuit www.nkkswitches.com J21 Keys (Switches) Keys (Switches) Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles